28
2009
09

塑膠注塑模使用行位(Slide側向抽芯)結构

 

1. 塑膠注塑模在什么情況下需要使用行位(Slide側向抽芯)結构。
A)有側凹或倒扣 B)側面(壁)不允許有出模角 C)包R枕位枕出有較大陰陽啤把嚴重影響產品外觀
2. 根据側凹位置,行位分內側行位和外側行位,按前后模又可分前模行位(行位在A板內滑動)和后模行位(行位在B板內滑動) 。前模行位常用較杯(前模哈夫Half)形式,因結构簡單,鎖模效果好,當不能采用較杯形式時,必須設計特殊結构的模胚,即面板与A板間應有一次分型。
...
28
2009
09

行业标准规范英汉对照-工艺装备2

151 GB/T 4257-1984 扩孔钻技术条件 Core drills--Technical requirements
152 GB/T 4258-1984 60°、90°、120°直柄锥面锪钻 Countersinks with parallel shanks for angles 60°90°and 120°inclusive
153 GB/T 4259-1984 锥面锪钻技术条件 Countersinks--technical requirements
...

28
2009
09

行业标准规范英汉对照-工艺装备

1 GB/T 967-1994 螺母丝锥 Nut taps
2 GB/T 968-1994 丝锥螺纹公差 Manufacturing tolerances on the threaded portion of taps
3 GB/T 969-1994 丝锥技术条件 Technical specification for taps
4 GB/T 970.1-1994 圆板牙 型式和尺寸 The types and dimensions for circular screwing dies
...

26
2009
09

Injection Mold Slide and lifter Standards

Injection Mold Slide and lifter Standards

Section 2: Slides/Lifters Standards and Design
Contents:
A) Mechanical injecion mold Slide Design Standards
B) Hydraulic injecion mold Slide Design Standards
B) Injection Mold Lifter Standard
...

26
2009
09

Demonstrate SLA process planning capabilities

Demonstrate SLA process planning capabilities that combine adaptive slicing and
orientation concerns with trade-offs among build time, surface finish, and accuracy.
 When building a part on SLA machine, sometimes a designer is interested in the best
...

26
2009
09

Plastic mold, Plastic mould

Mold or die are the common terms used to describe the tooling used to produce plastic parts in molding.

Traditionally, molds have been expensive to manufacture. They were usually only used in mass production where thousands of parts were being produced. Molds are typically constructed from hardened steel, pre-hardened steel, aluminium, and/or beryllium-copper alloy. The choice of material to build a mold from is primarily one of economics, steel molds generally cost more to construct, but their longer lifespan will offset the higher initial cost over a higher number of parts made before wearing out. Pre-hardened steel molds are less wear resistant and are used for lower volume requirements or larger components. The steel hardness is typically 38-45 on the Rockwell-C scale. Hardened steel molds are heat treated after machining. These are by far the superior in terms of wear resistance and lifespan. Typical hardness ranges between 50 and 60 Rockwell-C (HRC). Aluminium molds can cost substantially less, and when designed and machined with modern computerized equipment, can be economical for molding tens or even hundreds of thousands of parts. Beryllium copper is used in areas of the mold which require fast heat removal or areas that see the most shear heat generated.The molds can be manufactured by either CNC machining or by using Electrical Discharge Machining processes

...